A 3D Printing Project: Learning Through Trial and Error
撮影環境改善日記、その後
こんにちは!
ヒラヤマでインターンをしております、慶應義塾大学 環境情報学部2年の高橋理緒です。
以前のブログでは、商品撮影に使用するロール紙を棚に取り付けるため、3Dプリンタでオリジナルの部品を制作している様子をご紹介しました。
今回は、その後の進捗とともに、3Dプリンタでものを作るまでの流れについても、少しご紹介します!
「3Dプリンタ」と聞くと、専門的で難しそうな印象を持つ方も多いかもしれません。
でも、実際の流れは、「モデリング」で形を設計し、「スライシング」で素材や密度などの印刷条件を設定して、3Dプリンタで出力する、というもの。思っている以上に始めやすいんですよ!
私は普段、「Tinkercad」という初心者でも使いやすいモデリングツールを使っています。立方体や円柱などの基本的な形を組み合わせたり、穴を開けたりしながら、作りたい立体を設計していきます。
モデルが完成したら、今回は「Bambu Studio」というソフトウェアを使って「スライシング」を行います。スライシングとは、作成したモデルを、3Dプリンタが一層ずつ印刷できるデータに変換する作業です。
そのデータをSDカードに入れてプリンタに読み込ませると、画面上で設計したモデルが、少しずつ実物になっていきます。
3Dプリンタは大学にも設置されており、
私自身は普段、電子工作の授業や、趣味の制作に使っています。SFCでは男女を問わず多くの学生がこうした設備を使っている気がします。
ただし、3Dプリンタを操作できることと、思い描いたものを実際に使える形にすることは、また別の難しさがあります。
前回の記事から、少し大きさを変えたり、角度を調整したりしては、再び3Dプリンタで出力する作業を繰り返しましたが、残念ながら採用に至らなかった試作品がたくさんできました。
パソコンの画面上ではうまくいきそうに見えても、実物にすると、わずかな寸法の違いで取り付けられなかったり、固定が不安定になったりします。
そこで、同じ形を調整し続けるのではなく、部品の形状と固定方法そのものを考え直すことにしました。
これまでは、ロール紙を支えるS字フックそのものの形に合う部品を作ろうとしていました。
新しく考えたのは、S字フックにぴったり噛み合う形を目指すのではなく、フックの周囲を外側から固定する方法です。
イメージとしては、バーベルの重りが棒から抜け落ちないように取り付ける「バーベルカラー」に近いものです。フックの周りを挟み込むことで、位置がずれたり、外れたりすることを防げるのではないかと考えました。
新しい方向性は決まりましたが、まだ完成ではありません。
今回の部品は木の棒に取り付けるため、しっかりと固定しながら、棒を傷つけない方法を考える必要があります。部品と木の棒が接する面にゴムなどを挟み、滑りにくくする方法も検討しています。
頭の中で思い描いたものを、実際に使える形にするのは、想像していた以上に大変です。
それでも、うまくいかなかった試作品が増えるたびに、少しずつ問題点が見えるようになり、次のアイデアにもつながっています。
今回改善しようとしている撮影環境は、実際に社員の皆さんも不便を感じているものです。
だからこそできるだけ早く、使いやすい形で解決したいと思っています。
完成まで、もう少し試行錯誤は続きそうです!

In a previous blog post, I introduced my attempt to create an original 3D-printed part for attaching the roll paper used in our product photography setup to a shelf.
This time, I would like to share an update on the project, along with a brief introduction to how objects are made with a 3D printer.
When people hear the words “3D printer,” they may imagine something highly technical and difficult to use.
In reality, however, the basic process is simpler than many people expect. First, you design the shape through “modeling.” Next, you set printing conditions such as the material and density through “slicing.” Finally, you send the data to the 3D printer and print the object.
I usually use Tinkercad, a beginner-friendly modeling tool. By combining basic shapes such as cubes and cylinders, or cutting holes into them, I gradually build the three-dimensional form I want to create.
Once the model is complete, I use a program called Bambu Studio to carry out the slicing process. Slicing converts the model into data that tells the 3D printer how to build it one layer at a time.
After transferring the data to an SD card and loading it into the printer, the model designed on the screen slowly begins to take physical form.
There are also 3D printers available at my university. I use them both in my electronics classes and for personal projects. At SFC, students of all genders seem to use these facilities regularly.
However, being able to operate a 3D printer and being able to turn an idea into something that actually works are two very different things.
Since the previous article, I have repeatedly adjusted the size and angle of the part, printed a new version, and tested it again. Unfortunately, this process has produced many prototypes that were never suitable for actual use.
Even when a design looks as though it will work on a computer screen, a slight difference in dimensions can prevent it from fitting properly or make it unstable once it becomes a physical object.
Because of this, I decided not to continue making small adjustments to the same design. Instead, I began reconsidering both the shape of the part and the way it should be secured.
Until now, I had been trying to create a part that matched the exact shape of the S-hook supporting the roll paper.
My new idea is not to make something that fits perfectly into the S-hook, but rather to secure the hook from the outside.
The concept is similar to a barbell collar, which prevents weight plates from sliding off the bar. By clamping around the hook, the new part may be able to prevent it from shifting or coming loose.
Although I have now decided on a new direction, the design is not yet complete.
Because the part will be attached to a wooden rod, I need to find a way to secure it firmly without damaging the wood. I am also considering placing rubber or another material between the part and the rod to reduce slipping.
Turning an idea in my head into something that can actually be used has been much more difficult than I expected.
Still, each unsuccessful prototype has helped me understand the problem more clearly and has led me to the next idea.
The photography setup I am trying to improve is something that we genuinely find inconvenient.
That is why I hope to solve the problem as quickly as possible and create something that is truly easy to use.
It seems that the trial-and-error process will continue for a little while longer!